With a corpus of Rs 40 crore borrowed from Gujarat Fluorochemicals Limited, he started Inox Wind in 2009, at a time when major players like Suzlon and Bharat Forge were stumbling. But the Inox Group was looking to diversify, and given India’s energy deficit and the global thrust towards cleaner forms of energy, Devansh convinced his family of the power of wind. Neither his father nor his uncle Pavan (chairman and managing director of Inox Air Products) had prior experience in this sector. When he returned to India from the US in 2007, he shadowed his father Vivek (managing director, Gujarat Fluorochemicals Limited) for two years before deciding to enter the renewable energy sector. “We have a market cap of almost a billion-and-a-half dollars,” says Devansh, who, as director of his company, is the youngest family member to hold a position in the chemicals-to-multiplexes Inox Group. His company, Inox Wind, the renewable wind energy solutions provider, raised Rs 1,000 crore and was oversubscribed 18 times. In March 2015, the 28-year-old third-generation scion of Inox Group led one of the biggest initial public offerings (IPOs) that India has seen in the last two years. No one can accuse Devansh Jain of false pride. The Inox Group had no expertise in renewable energy, but backed by a successful IPO, third-generation scion Devansh Jain proved that there is profit in the sector 3 Small-Cap Stocks to Buy - Daily Stocks News on Inox Wind.Land Rover Media Hub – Nur ein weiteres Auto Bildideen on Manufacturing Facilities.Inox Login - Login Individual on Sitemap.INOX Wind: When promoters put in money in troubled business, it calls for deeper look.Inox Wind Board approves merger of Inox Wind Energy Limited into the Company.Inox Wind’s 3 MW Wind Turbine receives certification.Inox Wind’s 3MW Turbine gets Type Certification from Germany, paves way for commercial launch.Inox Wind receives Type Certification from TUV SUD for its 3 MW wind turbine.Attach the cat’s head to the top of the clock body by sticking the cat’s chin slightly underneath the larger paper plate using glue dots.Draw some triangle stripes and stick to the right-hand side of the cat clock body with glue dots. Draw a wiggly cat’s tail onto orange foam, cut out.Using a black marker pen, draw a mouth and whiskers, and 3 triangle stripes between the ears. Using a smaller paper plate for the cat’s head, stick on 2 jumbo wiggle eyes.Cut out a small round circle of pink foam for the nose, and stick in place with a glue dot. Cut these out and stick them to the back of the small orange paper plate using glue dots. Draw 2 rounded triangles for the cat’s ears onto a sheet of orange foam.Between these thick lines, draw 4 short thin lines to mark the seconds around the clock.Using a dark coloured pen, draw a thick line roughly 3cm long pointing to each number around the dimpled edge of the plate. Pierce the paper fastener attached to the arrows through the middle of the paper plate and open up the fastener at the back to secure in place. Mark the centre of the paper plate circle using a pencil.Cut out both arrows and attach the ends together by placing the arrows on top of each other and then putting a paper fastener pin through them both at the bottom.Then draw another arrow roughly 1cm (W) by 4.5cm (L) onto the same sheet of green foam. To make the clock hands, draw an arrow roughly 1cm (W) by 6.5cm (L) onto a sheet of green foam.Follow by sticking No.6 bottom centre, No.3 right-hand centre and No.9 left-hand centre. To help place the numbered circles evenly around the clock face, stick the No.12 at the top centre of the plate as shown inside the dimpled edge with a glue dot.Then number them 1-12 using a dark coloured marker pen. Repeat until you have drawn 12 small circles. Using a pencil, draw around the lid of a glue stick or similar sized circular object onto a sheet of yellow foam.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |